[Cecil]

My biggest problem besides not having time, is when I do have time Im constantly interupted. Not exactly a good thing to happen if using DICE or LN2 lol

[Neuromancer]

GTLREFs stock should be 67 for core 1/3 and 71 for 2/4 stock I think

Dont raise them too much. I raised mine to 77 each in my quest to bench a G0 at 500 BUS and fried my chip.

[Cecil]

Originally Posted by Neuromancer

GTLREFs stock should be 67 for core 1/3 and 71 for 2/4 stock I think

Dont raise them too much. I raised mine to 77 each in my quest to bench a G0 at 500 BUS and fried my chip.

Thats what they are on normal boards. DFI doesnt use the normal set values, they use percentages.

[Chuchnit]

Those values he is talking about is percentages, but I'm sure DFI being who they are that its done different.

[ReverendMaynard]

was kicking around some old posts Cecil, and found these settings for 500+ FSB. Looks like GTL Ref control is disabled.

Notice the PCIE freq? Remind you of another intel platform?


BIOS SETTING

CPU Feature
- Thermal Management Control: Disabled
- PPM(EIST) Mode: Disabled
- Limit CPUID MaxVal: Disabled
- CIE Function: Disabled
- Execute Disable Bit: Disabled
- Virtualization Technology: Disabled
- Core Multi-Processing: Enabled

Exist Setup Shutdown: Mode 2
CLOCK VC0 divider: AUTO
CPU Clock Ratio Unlock: Enabled
CPU Clock Ratio:7
- Target CPU Clock:3605
CPU Clock:515
Boot Up Clock:auto
DRAM Speed:266/667
- Target DRAM Speed:1206
PCIE Clock: 110mhz

Voltage Settings
CPU VID Control:1.365
CPU VID Special Add:auto
DRAM Voltage Control:2.47
SB 1.05V Voltage:1.217
SB Core/CPU PLL Voltage:1.95
NB Core Voltage:1.74
CPU VTT Voltage:1.38
Vcore Droop Control: Disabled
Clockgen Voltage Control: 3.75v
GTL+ Buffers Strength: Strong
Host Slew Rate: Weak
GTL REF Voltage Control: Disable
x CPU GTL1/3 REF Volt: 110
x CPU GTL 0/2 REF Volt: 110
x North Bridge GTL REF Volt: 110

DRAM Timing
- Enhance Data transmitting: FAST
- Enhance Addressing: FAST
- Channel 1 CLK fine delay: CURRENT[14]
- Channel 2 CLK fine delay: 13

CAS Latency Time (tCL): 5
RAS# to CAS# Delay (tRCD):4
RAS# Precharge (tRP):4
Precharge Delay (tRAS):12
All Precharge to Act: AUTO
REF to ACT Delay (tRFC): AUTO
Performance Level: AUTO
MCH ODT Latency: AUTO
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Read to Write Delay (tRDWR): AUTO
Ranks Write to Write (tWRWR): AUTO
Ranks Read to Read (tRDRD): AUTO
Ranks Write to Read (tWRRD): AUTO
Read CAS# Precharge (tRTP): AUTO
ALL PRE to Refresh: AUTO

PCIE Slot Config: 1X 1X
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
SATA Spread Spectrum: Disabled

[Splave]

Originally Posted by DOM

why do you say that ?? i wanted to get a cpu pot lol

also GL ceecil i been trying to get time to fire up my ss and a p4 & p5b dlx which i havent used in like 2yrs lol

Its fun as hell but you will no longer have a life, addicted.

[DOM]

Originally Posted by Splave

Its fun as hell but you will no longer have a life, addicted.

2 kids i dont have a life lol and hrs i work they suck also

but when i pay all the extra bills off... ill make time cuz ill have the cash to buy more stuff i hope i can next yr on income tax :p

[Cecil]

Getting decent clocks, and good wprime and spi 1m runs. My pifast scores are about 4 seconds slower then they should be, and spi 32m doesnt seem to want to run at all. Got up to 4140 so far, not sure if I can get it higher though. Took over 1.7v for that.

[Chuchnit]

Sweet man. It seems like you picked up on the DFI bios quick. I hear they are cumbersome. Got any screenies?

[Cecil]

I was also able to get the ram benchable at 1150Mhz 4-4-4-4-22 with PL7.