I Really like this board
http://valid.canardpc.com/show_oc.php?id=1189116
Water (not pushing past 1.45 on water)
Code:
Target CPU Frequency 4883MHz
Target DRAM Frequency 1576MHz
LN2 Mode: Disabled***
QPI Loadline Calibration: Enabled***
Sync Mode [Enabled]
AI Overclock Tuner [Manual]
OC From CPU level Up [Auto]
CPU Ratio Setting [31.0]
CPU Turbo Power Limit [Disabled]
>CPU Configuration----------------------------
CPU Ratio Setting [31.0]
C1E Support [Disabled]
Hardware Prefetcher [Enabled]
Adjacent Cache Line Prefetcher [Enabled]
Intel(R) Virtualiyation Tech [Disabled]
CPU TM Function [Disabled]
Execute Disable Bit [Disabled]
Intel(R) HT Technology [Disabled]
Active Processor Cores [All]
A20M [Disabled]
Intel(R) SpeedStep(TM) Tech [Disabled]
Intel(R) C-STATE Tech [Disabled]
C State package limit setting [Auto]
----------------------------------------------
BCLK Frequency [158]
PCIE Frequency [100]
DRAM Frequency [1576]
UCLK Frequency [3258]
QPI Link Data Rate [4.8mt/s]
Memory Configuration Protect [enabled]
>DRAM Timing Control--------------------------
CAS# Latency 6 [8]
RAS# to CAS# Delay 7 [8]
RAS# PRE Time 6 [8]
RAS# ACT Time 18 [24]
RAS# to RAS# Delay 4 [auto]
REF Cycle Time 72 [88]
WRITE Recovery Time 12 [auto]
READ to PRE Time 6 [auto]
FOUR ACT WIN Time 24 [Auto]
Back-To-BackCAS# Delay 0 [Auto]
Timing Mode 1N [1N]
Round Trip Latency on CHA 60 [auto]
Round Trip Latency on CHB 62 [auto]
Round Trip Latency on CHC 64 [auto]
WRITE To READ Delay(DD) 8 [Auto]
WRITE To READ Delay(DR) 8 [Auto]
WRITE To READ Delay(SR) 18 [Auto]
READ To WRITE Delay(DD) 7 [Auto]
READ To WRITE Delay(DR) 7 [Auto]
READ To WRITE Delay(SR) 7 [Auto]
READ To READ Delay(DD) 7 [Auto]
READ To READ Delay(DR) 6 [Auto]
READ To READ Delay(SR) 4 [Auto]
WRITE To WRITE Delay(DD) 8 [Auto]
WRITE To WRITE Delay(DR) 8 [Auto]
WRITE To WRITE Delay(SR) 18 [Auto]
----------------------------------------------
CPU Differential Amplitude [1000]
CPU Clock Skew [Auto]
IOH Clock Skew [Auto]
------------ Extreme Engine Digi+ ------------
Digi+ PWR Mode [T-Balanced]
PWR Volt. Control [7v]
Load-Line Calibration [50%]
CPU Voltege OCP [Disabled]
CPU PWM Frequency [800kHz]
Extreme OV [Disabled]
Extreme OC [Auto]
CPU Voltage 1.415 [1.442]
CPU PLL Voltage 1.812 [1.808]
QPI/DRAM Core Voltage 1.310 [1.400]
DRAM Bus Voltage 1.654 [1.683]
>DRAM REF Voltages----------------------------
DRAM DATA REF Voltage on CHA [Auto]
DRAM CTRL REF Voltage on CHA [Auto]
DRAM DATA REF Voltage on CHB [Auto]
DRAM CTRL REF Voltage on CHB [Auto]
DRAM DATA REF Voltage on CHC [Auto]
DRAM CTRL REF Voltage on CHC [Auto]
----------------------------------------------
IOH Voltage 1.244 [1.202]
IOH PCIE Voltage 1.508 [auto]
ICH Voltage 1.111 [1.202]
ICH PCIE Voltage [Auto]
---------- Spread Spectrum Control -----------
CPU Spread Spectrum [Disabled]
DRAM Spread Spectrum [Disabled]
***on-board jumper dependant
Full LLC cause a bit of overvolt for me, 50% seems good. PWR volt control over 8v not necessary on water. Will try some higher bclk stuff and report back.