My biggest problem besides not having time, is when I do have time Im constantly interupted. Not exactly a good thing to happen if using DICE or LN2 lol

GTLREFs stock should be 67 for core 1/3 and 71 for 2/4 stock I think

Dont raise them too much. I raised mine to 77 each in my quest to bench a G0 at 500 BUS and fried my chip.

Thats what they are on normal boards. DFI doesnt use the normal set values, they use percentages.

Those values he is talking about is percentages, but I'm sure DFI being who they are that its done different.

was kicking around some old posts Cecil, and found these settings for 500+ FSB. Looks like GTL Ref control is disabled.

Notice the PCIE freq? Remind you of another intel platform?


BIOS SETTING

CPU Feature
- Thermal Management Control: Disabled
- PPM(EIST) Mode: Disabled
- Limit CPUID MaxVal: Disabled
- CIE Function: Disabled
- Execute Disable Bit: Disabled
- Virtualization Technology: Disabled
- Core Multi-Processing: Enabled

Exist Setup Shutdown: Mode 2
CLOCK VC0 divider: AUTO
CPU Clock Ratio Unlock: Enabled
CPU Clock Ratio:7
- Target CPU Clock:3605
CPU Clock:515
Boot Up Clock:auto
DRAM Speed:266/667
- Target DRAM Speed:1206
PCIE Clock: 110mhz

Voltage Settings
CPU VID Control:1.365
CPU VID Special Add:auto
DRAM Voltage Control:2.47
SB 1.05V Voltage:1.217
SB Core/CPU PLL Voltage:1.95
NB Core Voltage:1.74
CPU VTT Voltage:1.38
Vcore Droop Control: Disabled
Clockgen Voltage Control: 3.75v
GTL+ Buffers Strength: Strong
Host Slew Rate: Weak
GTL REF Voltage Control: Disable
x CPU GTL1/3 REF Volt: 110
x CPU GTL 0/2 REF Volt: 110
x North Bridge GTL REF Volt: 110

DRAM Timing
- Enhance Data transmitting: FAST
- Enhance Addressing: FAST
- Channel 1 CLK fine delay: CURRENT[14]
- Channel 2 CLK fine delay: 13

CAS Latency Time (tCL): 5
RAS# to CAS# Delay (tRCD):4
RAS# Precharge (tRP):4
Precharge Delay (tRAS):12
All Precharge to Act: AUTO
REF to ACT Delay (tRFC): AUTO
Performance Level: AUTO
MCH ODT Latency: AUTO
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Read to Write Delay (tRDWR): AUTO
Ranks Write to Write (tWRWR): AUTO
Ranks Read to Read (tRDRD): AUTO
Ranks Write to Read (tWRRD): AUTO
Read CAS# Precharge (tRTP): AUTO
ALL PRE to Refresh: AUTO

PCIE Slot Config: 1X 1X
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
SATA Spread Spectrum: Disabled

Its fun as hell but you will no longer have a life, addicted. :thumbsup:

2 kids i dont have a life lol and hrs i work they suck also

but when i pay all the extra bills off... ill make time cuz ill have the cash to buy more stuff i hope i can next yr on income tax :p

Getting decent clocks, and good wprime and spi 1m runs. My pifast scores are about 4 seconds slower then they should be, and spi 32m doesnt seem to want to run at all. Got up to 4140 so far, not sure if I can get it higher though. Took over 1.7v for that.

Sweet man. It seems like you picked up on the DFI bios quick. I hear they are cumbersome. Got any screenies?

I was also able to get the ram benchable at 1150Mhz 4-4-4-4-22 with PL7.