[Hondacity]

Biostar TPower I45 (P45) Tpower Biostar I45 (P45)
SetFSB(By abo)PLL IC:ICS 9LPRS926EGLF・・・ICS 9LPR918BKLなどで使用可能。 Setfsb(By abo)PLL IC:ICS ICS 9Lpr918Bkl 9Lprs926Eglf · · · and available.
Memset(By FELIX) Memset(By FELIX)
Vcore-mod & Vdroop pencile-mod(HB) :実戦では、これまでどうり50～100KΩ VRでOK Pencile-mod-mod Vcore & Vdroop (HB) : In battle, in 50 ~100KΩVR Douri OK so far
Vdroopの方はちょいと不完全かも（^^;; Choi will be incomplete and those Vdroop (^^;;
Vnb-mod :実戦では10～20KΩ VRが調節しやすい。 VNB-mod : 10 ~ 20KΩ VR in combat is easy to adjust.
Vddr-mod :実測でBiosより≒0.03 ～ 0.07V 多めに出力されています。 Vddr-mod : Experimental results from Bios ≒ 0.03 ~ 0.07V output is a lot.
Vfsb-mod & Measur point (2008.6.16-6.17 by Hideo) 08.06.17 Vfsb-mod & Measur Point (2008.6.16-6.17 by Hideo) 08.06.17
New Bios New Bios ここが便利(起動直後F12で AMIflash呼び出し、 USB内の目的bios指定) This is convenient (F12 at boot just after the call AMIflash, USB purpose specified in the bios)
P45AA626.rar ( Vnb-Vfsb連動解 除 08.06.30 ) P45Aa626.rar (VNB-linked Vfsb release 08.06.30)
格安温度計キット（～ -200℃以下/ﾌﾟﾛ-ﾌﾞ次第）：LN2で-56～-196℃測定用に調整済み Thermometer kits cheap (less than ~ -200 ℃ / - profile - up゙off):LN 2 - -196 -56 ℃ adjusted for measurement
ここ3年位、温度計の調子が悪いので、あまり使用していませんでした（笑） Place the past three years, because of the bad condition of the thermometer was not used much (laughs)
ま、限界でπ焼くだけなので、調子悪ければ悪かったで、無くても何とかなるわけですがさすがに、突沸付近で8min程度、最適温度を維 持管理するのは、人間技ではありませぬ。 Well, just because the limit π burn, at worst in bad shape, indeed even without that it becomes something, bumping around 8min extent, to maintain optimum temperature, the technique Arimasenu man.
本体は、完全にだめになりましたがＫ型 熱電対プローブは、1本未使用品が出てきました。 The body is now completely ruined K-type thermocouple probe will have a single out unused items.
で、久々に秋月から、昔ながらの定番ｷｯﾄを再度購入しました。 In a long time to Akizuki from a kit I bought back the old classic. ま、以前と変わっていません。 Well, not changed before.
半田の数が多いので、ちょいとめんどくさいのですが、非常に簡単な構造なのでﾌﾟﾗﾓ感覚でOKです。 Since a large number of solder, but Choi is troublesome and, in the sense゚Lhamo off a very simple structure, so it is OK.
そろそろ、 本体だけ 、カッコイイ既製品をとも思いましたが、やっぱ、ﾊﾟﾊﾟはこ んなんが好きで～す。 It's time to just the body, cool shelf is also a thought, expected, like゚Hakonnanga Ha Ha Year.
性能はVRで調整可能なので、使用前にLN2で温度調整すれば、必要十 分と思います。 VR performance is so adjustable, you should tune LN2 temperature before use, and I think necessary and sufficient.
ま、だけど、 見栄えが良くないの で、あんまし、ﾋﾄに見せられないのよね～（笑） 08.08.28 Well, but, not good looking , so Anmashi, I'm not show-human (laughs) 08.08.28
E8600(E0) E8600 (E0)
Q820A599/2V:1.250V/648.3MHz/4.407G(1CPU_4.447G)・・0.63/0.63 /0.56 400/200 PLL 1.70 V Vfsb 1.476 V Q820A599/2V: 1.250V/648.3MHz/4.407G (1CPU_4.447G) · · 0.63/0.63 / 0.56 400/200 PLL 1.70 V Vfsb 1.476 V
6.30G(2.016V/-135 ℃)7.359s Ver5.1 : 10x570MHz起動/CL=5の最速風設定PL= 10 5-4-4-4 6.30G (2.016V/-135° C)7.359S Ver5.1: 10X570Mhz start / CL = setting the fastest winds 5 PL = 10 5-4-4-4
6x650MHz (Bios626 FSB570起動DDR2 Enhance Mode : enabled 5-4-4-6 PL=9 /CPU & North cooling: LN 2 ) 6x650MHz (Bios626 FSB570 start DDR2 Enhance Mode: enabled 5-4-4-6 PL = 9 / CPU & North cooling: LN 2)
Vnb1.765V Vfsb1.47V　MAXXNEO -138 ～ -140℃ Vnb1.765V Vfsb1.47V MAXXNEO -138 ~ -140 ℃
8m 2m19.563 32m 11m8.969 8M 2M19.563 32M 11M8.969 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　 08.08.21 08.08.21
Biostar TPower I45(Ver5.1):最速風設定で良く廻りますが緩めても FSB690MHzが限界な板 Biostar TPower I45 (Ver5.1): Even the fastest-like setting loose a good廻Rimasu FSB690MHz plate limit
《System》 "System"
CPU: E8500 CPU: E8500
M/B: #2 BIOSTAR TPower I45 ( Bios P45AA 626 .bsp Ver5.1 ) M / B: # 2 BIOSTAR TPower I45 (Bios P45AA 626. Bsp Ver5.1)
CPU Cooling : Air cooling+ V-TEC ARC Bed Rev3.3 by Vigor CPU Cooling: Air cooling + V-TEC ARC Bed Rev3.3 by Vigor
Chipset Cooling :ﾉ -ﾏﾙｼﾝｸ + FAN 4cm 6200r.pm Chipset Cooling: Bruno - Sink Thermal + FAN 4cm 6200r.pm
Memory: A-DATA DDR2 1200+ 1GB×2 Memory: A-DATA DDR2 1200 + 1GB × 2
VGA: ATI RageXL (PCI) VGA: ATI RageXL (PCI)
HDD: Raptor 36G HDD: Raptor 36G
Power Supply: SilverStone Power Supply: SilverStone 　 SST-OP850 SST-OP850
OS：Windows 2003 備 考：グリス :普通のﾎﾜｲﾄｸﾞﾘｽ OS: Windows 2003 Note: Grease: listening and ordinary Howaitoku
#2 : # 2: BIOS Setting BIOS Setting
CPU Frequency Setting : 570MHz起動（SetFSBでup） CPU Frequency Setting: 570MHz boot (SetFSB on up)
Over Clock Retry Count : 1 Over Clock Retry Count: 1
FSB(Bsel) To NorthBridge Latch : 1333 （この 板は、 autoで伸びない ） FSB (Bsel) To NorthBridge Latch: 1333 (this board, auto inelastic in)
DRAM Frequency : 1:1/FSBx2 DRAM Frequency: 1:1 / FSBx2
DDR2 Enhance Mode : enabled （この板は、 disableで何故か、伸びない ） DDR2 Enhance Mode: enabled (this board, disable the reason, inelastic)
FSB Compensation FineTune ： enabled FSB Compensation FineTune: enabled

DRAM Timing Configuration DRAM Timing Configuration
DDR2 RCOMP Configuration : Configuration 2 DDR2 RCOMP Configuration: Configuration 2
Static tREAD Value : Auto Static tREAD Value: Auto
Configure DRAM Timing by SPD : Disable Configure DRAM Timing by SPD: Disable
(5-4-4-12-6-33-6-6-6)→ あとは、MemsetでOS上で適当に調整 (5-4-4-12-6-33-6-6-6) → is then, Memset proper adjustment on the OS

Clock Gen Configuration Clock Gen Configuration
PCIE Frequency Setting : 101 PCIE Frequency Setting: 101
CPU Clock Skew Control : 400ps CPU Clock Skew Control: 400ps
(G)MCH Clock Skew Control : 200ps (G) MCH Clock Skew Control: 200ps
CPU Clock Driving Control : Auto CPU Clock Driving Control: Auto

Voltage Configuration Voltage Configuration
Chipset Voltage : +0.500V Chipset Voltage: +0.500 V
FSB Voltage : +0.350V FSB Voltage: +0.350 V
CPU Core1 GTL Ref Voltage : 0.63*VTT CPU Core1 GTL Ref Voltage: 0.63 * VTT
CPU Core2 GTL Ref Voltage : 0.63*VTT CPU Core2 GTL Ref Voltage: 0.63 * VTT
MCH GTL Ref Voltage : 0.56*VTT MCH GTL Ref Voltage: 0.56 * VTT
CPU PLL Voltage:1.70V CPU PLL Voltage: 1.70V
1m_FSB 666.6 MHz（air cooling/室温26℃） Vali FSB 672 MHz (air cooling/室温26℃) Vnb1.752V Vfsb1.486V 08.08.01 1m_FSB 666.6 MHz (air cooling / ℃ 26 at room temperature) Vali 672 MHz FSB (Air Cooling / 26 ° C room temperature) Vnb1.752V Vfsb1.486V 08.08.01


**will attach pics later...

[FACE]

Hey Honda, is there anyway you can clean that ^ up a bit? It looks terrible.

Seriously, though.... it is very difficult to read through.

Thanks dood.

[Hondacity]

google translate

i'll clean it up a little...later

i just copy pasted it for future ref....

[OC Maximus]

Biostar TPower I45 (P45)

Setfsb (By Abo) PLL IC: ICS ICS 9Lpr918Bkl 9Lprs926Eglf · · · and available.
Memset (By FELIX)

Vcore mod-mod-Pencile & VDROOP (HB) : The battle is far Douri 50 ~ 100k VR is OK
Maybe those little imperfect Vdroop 　
VNB-mod : The battle will be easy to adjust 10 ~ 20KΩ VR.
VDDR-mod : Experimental results from Bios ≒ 0.03 ~ 0.07V output is a lot.
Vfsb-mod & Measur Point (2008.6.16-6.17 by Hideo) 　　　　　　　　　　　　　　　　　　　　08.06.17

New Bios this is convenient (immediately after the start F12 AMIflash call in, USB purpose specified in the bios)
　　　　　　　P45Aa626.rar ( VNB-linked Vfsb release 　08.06.30 )

Yasushi Tadasu thermometer kit (below -200 ℃ / - profile - as soon as s off): LN two at -56 ℃ ~ -196 calibrated to measure

Place the past three years because of the bad condition of the thermometer was not used much (laughs)
Well, so bake in the limit of π, at worst in a bad condition, but somehow even without a reason
Indeed, bumping around 8min about the optimum temperature to maintain, in humans, there is no technique.
The body is now completely useless type K thermocouple probe has been an unused one out.

In a long time to Akizuki from a kit bought back the old classic. Well, not changed before.
Since a large number of solder and I little troublesome, because the feeling Lhamo ゚ off a very simple structure is OK.
Soon, only the body , ready-made cool but also thought, and I thought, like゚Hakonnanga Ha Ha Year.
VR performance is so adjustable, you can adjust the temperature before using LN2, and I think necessary and sufficient.
Well, but, good-looking , so Anmashi, right - humans can not see (laughs) 　　08.08.28

E8600 (E0)
Q820A599/2V: 1.250V/648.3Mhz/4.407G (1Cpu_4.447G) · · 0.63/0.63 / .56 400/200 PLL 1.70 V Vfsb 1.476 V

6.30G (2.016V/-135 ° C.) 7.359S Ver5.1 : 10X570Mhz Start / CL = PL = 5 set the fastest winds ten 5-4-4-4

6X650Mhz (Bios626 Fsb570 DDR2 Enhance Mode boot: enabled 5-4-4-6 PL = 9 / CPU Cooling & North: LN two )
Vfsb1.47V Vnb1.765V Maxxneo -138 ~ -140 ° C.
8M　2M19.563 　32m 11M8.969 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　 08.08.21

Biostar TPower I45 (Ver5.1): Loosen the廻Rimasu even better in the wind set the fastest plate limit FSB690MHz

"System"
CPU: E8500
M / B: # 2 BIOSTAR TPower I45 ( Bios P45Aa six hundred twenty-six . bsp Ver5.1 )
CPU Cooling : Air Cooling Bed + V-TEC ARC Rev3.3 by Vigor
Chipset Cooling : Bruno - Sink Thermal + FAN 6200R.pm 4cm
Memory: A-DATA DDR2 + 1GB × two one thousand two hundred
VGA: ATI RageXL (PCI)
HDD: Raptor 36G
Power Supply: SilverStone 　SST-Op850
OS: Windows 2003　Note: grease: grease normal Howaitoku

# 2: BIOS Setting　
Setting CPU Frequency : 570Mhz boot (SetFSB on up)
Over Clock Retry Count: 1
FSB (BSEL) NorthBridge To Latch: 1,333 (this board, stretching in auto )
DRAM Frequency: 1:1 / FSBx2
DDR2 Enhance Mode: enabled (this board, why disable, and stretching )
FineTune FSB Compensation : enabled

DRAM Timing Configuration
DDR2 RCOMP Configuration: Configuration 2
Static tREAD Value: Auto
Configure DRAM Timing by SPD: Disable
(5-4-4-12-6-33-6-6-6) → After that, Memset suitably adjusted on the OS

Clock Gen Configuration
PCIE Frequency Setting: 101
CPU Clock Skew Control: 400ps
(G) MCH Clock Skew Control: 200ps
CPU Clock Driving Control: Auto

Voltage Configuration
Chipset Voltage: +0.500 V
FSB Voltage: +0.350 V
CPU Core1 GTL Ref Voltage: 0.63 * VTT
CPU Core2 GTL Ref Voltage: 0.63 * VTT
MCH GTL Ref Voltage: 0.56 * VTT
CPU PLL Voltage: 1.70V　

OCM

[Hondacity]

perfect

[Hondacity]

another one from jp...

Setup

Max Clock SP-Pi Pi-fast

M/B: BIOSTAR I45 Ver.5.1 no-mod
M/B Bed: V-TEC ARC Bed
CPU:Core2 Duo E8500 Q813A227
CPU cooling:MaxxNeo + LN2 / Temp:-140C
Chipset Cooling: kuripro2 + LN2 / Temp:-100C
Mem:Team PC2-10400 C6 1GB x2
VGA:Matrox Millennium PCI
HDD:IBM DTLA 307030(P-ATA)
PSU: SilverStone ZEUS-1200
OS: Windows Server 2003 & XP-SP1
Tools: SetFSB / Memset3.5 / P965StrapTweaker/ ERAM2.11 /
Memset Setup: 5-5-5-15-6-AUTO....

[BIOS SETUP]　O.N.E
Over-Clocking Navigator [Manual OverClock]
Intel(R) SpeedStep(tm) : Disabled
Ratio CMOS Setting : ×9.5
CPU Frequency Setting : 600
Over Clock Retry Count : 3
FSB(Bsel) To NorthBridge Latch : AUTO
DRAM Frequency : DDR2-1200
DDR2 Enhance Mode : Disabled

DRAM Timing Configuration
DDR2 RCOMP Configuration : Configuration 4
Static tREAD Value : Auto
Configure DRAM Timing by SPD

Clock Gen Configuration
PCIE Frequency Setting : 100
CPU Clock Skew Control : 200ps
(G)MCH Clock Skew Control : AUTO
CPU Clock Driving Control : AUTO

Voltage Configuration
CPU Voltage : +0.850v (Actual:1.96V)
DDR Voltage : +0.700v (Actual:2.64V)
Chipset Voltage : +0.350v
FSB Voltage : AUTO
MCH GTL Ref Voltage : Auto
CPU PLL Voltage : AUTO