[ny_driver]

So I just tried running 32m @ 5100MHz(bclk 243)........did fine @ 5000MHz w/ only 1.506 vcore and 1.547 qpi.
1.537 vcore,
1.555 qpi,
1.685 ddr,
1.197 ioh,
1.540 ich
memory @ 971MHz 7-9-7-23-78
qpi link @ 2914
NB @ 4372.

It crashed BSOD ~ halfway through 32m. I then proceeded to lower the NB a notch to 3886 and it crashed BSOD part way through copy waza.

Any suggestions?

Thanks.

[Splave]

nice chip! faster then mine on single stage

[ny_driver]

There's more where that came from.
Might try a little more vcore or something for 1 more run before I tear it down and wait for new HD and the rest of my triple channel kit.

Also need to check under the block for moisture....the chiller has been on there a few days now and it was my first time sealing one of these in. All I used was eraser.

EDIT: here's what it looked like. Just the slightest bit of dampness on the towels right around the chip. Perfectly dry and sealed in tight IMHO.

Check out the thermal paste though, not sure how it got like that. I did use more than normal for some reason, but it looks weird. Has to be caused my moisture. I've never had that happen before, and I know it was squished down tight to the cpu....the surface of this chip is nowhere near as smooth as an AMD.

afterthought: I don't think it was seated good even though the temps were pretty good. Under load @ 4.8Ghz they were outrageous. There cannot be any insulation between the head of the block and the hold-down plate. NP.

[Splave]

raise trfc a couple notches?
what was the bsod code

[ny_driver]

No code it was just a quick BSOD then restart with failed OC messages.

The memory is fine in 32m up to 1050MHz @ those timings.

EDIT: ohh yeah I need to set it so it does not auto-restart upon BSOD.

[ny_driver]

I live for double posting.......

Anyways I got it to run pifast @
cpu=5100MHz
uncore/nb=4370
qpi link=2900
ddr=971MHz/7-9-7-23-78

vcore=1.53v
uncore/qpi=1.33v(dunno why I had it so high before)
ddr=1.69v
ioh=1.197v
ich=1.54v

(All these voltages may still be higher than necessary and causing insability)

Haven't tried spi yet with less uncore/qpi voltage. I should be able to run it at least as high because I'll only be using 1 core for that.

I'll report back later.

[DOM]

try ioh/ich 1.25-1.35v both the same

[ny_driver]

Well guys, maybe 104 points is all I can do with the cooling I have available. I might get like 10-20 more points with better cooling.

When I'm single core benching it's hitting ~15C and with wprime it's hitting like 50-60C. I need to get a better water-block for the chiller for one thing.

So I seem to be banging my head on the wall now. I just don't know what to increase and it seems like a million possibilities.......along with the possibility that it just may not go any further without being subzero.

I'm sure I'll keep trying, but what do you guys think?


http://hwbot.org/community/submissio...920_5184.9_mhz

http://hwbot.org/community/submissio..._920_16.56_sec

http://hwbot.org/community/submissio...920_7sec_969ms

http://hwbot.org/community/submissio...in_19sec_516ms

http://hwbot.org/community/submissio..._920_5sec_54ms

http://hwbot.org/community/submissio...in_40sec_524ms

[DOM]

i say u did an awsome job to be just on a chiller

[ny_driver]

Thanks DOM.

I guess I should get some 3d benches installed tomorrow, I have some 3d studying to do though.

I have 3 unmodded gpus I can bench on chilled water.........4890, 4850, and 8800GTS 640. Should be able to scrounge up a few points there, even with a 920........I hope.