LN2 by Christmas...mark my words! - Page 13

DOM · #**121** 12-30-2010

idk if theres other here idk how to look for them but i think there is but airgas didnt rent out tanks also damn mofos said it was also the same even if i had a bigger tank

ny_driver · #**122** 12-30-2010

I took my dremel to the top and gutted the middle, except the red lever, cleaned up the hole, and now it pours a nice predictable, strong, straight stream. It could leak out the lever hole if you tip it upside down way too far. It works awesome.

Check it out.

There has gotta be other welding supply places around. There is 3 around here...1 local, Airgas, and Haun...and I live 40-50 miles from anywhere major....and by major I mean small cities.

DOM · #**123** 12-30-2010

thats what i did but with a box cutter i dont have a dermel but cut my leg when doing it i stll got the mark lol

oh thats what there called i was looking for ln2 places

ny_driver · #**124** 12-30-2010

lol x2....try Lubbock Welding Supply...that was all I could really find.

EDIT: I butchered it with the dremel, no tools for really cutting plastic....fortunately it didn't need to look pretty.

Kal-EL · #**125** 12-30-2010

I totally butchered the crap outa mine, unusable now, hehe

ny_driver · #**126** 12-31-2010

Perhaps a little tutorial is in order here?

....wait, is that a hole in your leg?

EDIT: picture added

I should have used a hole-saw.

ny_driver · #**127** 12-31-2010

Having nothing but problems here this time. Thermometer stops at -110 and I don't know what the damn problem is. LEDS indicate DRAM.............. Got it going with 1 in the last slot.....think frost built up in the 1st DIMM slot with the stick in there, but that didn't happen last time. I don't even know what the frack I'm doing about some of this I just realized......lol.....I learn well the hard way. It seemed so easy the first time....beginners luck?
Time to take a step back for a few.

(yes of course it's Jerry

)

DrNip · #**128** 12-31-2010

I had the same problem with my temp gauge except it stopped at -130. It was like trying to see in the dark and sucked. Ended up ruining my last session.

Watch the language bro, PG-13 forum here. I ninja edited your post for ya.

ny_driver · #**129** 12-31-2010

Quote:

Originally Posted by DrNip

I had the same problem with my temp gauge except it stopped at -130. It was like trying to see in the dark and sucked. Ended up ruining my last session.

Watch the language bro, PG-13 forum here. I ninja edited your post for ya.

I ran the 1090T w/ LN2 the other day with no problems and the same thermometer. Now I can't get it to OC at all with 1 in the last slot.....gotta mess with it for awhile.

My bad, thanks.

EDIT: 1st slot works again

EDIT: Dual Channel works too, then I poured a bunch of LN2 while in bios and it froze up and now acts same DRAM.

ny_driver · #**130** 12-31-2010

Every time I think I've got it straightened out it freezes up again. I don't know...either this 1090 , or my memory or who knows what. Guess I should try another CPU. It's all work now.

...yup now according to the board the cpu is bad....gonna pop the 965 in there.

EDIT: everything works fine with the 965.......what a waste of time and resources. I'm going to bed because I have a bad seat on the 965 because I was too lazy to warm the pot up and put good TIM in there when I switched cpus. I'll remount it in the morning and use up this juice....what I didn't waste. My eyes are beat and I'm already partially soured o the experience for now.

Happy New Years anyways. Tomorrow will be a better day at least with the 965. Wonder what the problem with the 1090T is....I've been using it.